The influences of stress on the properties of In GaN/GaN multiple quantum wells(MQWs) grown on silicon substrate were investigated.The different stresses were induced by growing In GaN and Al GaN insertion layers(IL) respectively before the growth of MQWs in metal–organic chemical vapor deposition(MOCVD) system.High resolution x-ray diffraction(HRXRD) and photoluminescence(PL) measurements demonstrated that the In GaN IL introduced an additional tensile stress in n-GaN,which released the strain in MQWs.It is helpful to increase the indium incorporation in MQWs.In comparison with MQWs without the IL,the wavelength shows a red-shift.Al GaN IL introduced a compressive stress to compensate the tensile stress,which reduces the indium composition in MQWs.PL measurement shows a blue-shift of wavelength.The two kinds of ILs were adopted to In GaN/GaN MQWs LED structures.The same wavelength shifts were also observed in the electroluminescence(EL) measurements of the LEDs.Improved indium homogeneity with In GaN IL,and phase separation with Al GaN IL were observed in the light images of the LEDs.
Crack-free Ga N/In Ga N multiple quantum wells(MQWs) light-emitting diodes(LEDs) are transferred from Si substrate onto electroplating Cu submount with embedded wide p-electrodes. The vertical-conducting n-side-up configuration of the LED is achieved by using the through-hole structure. The widened embedded p-electrode covers almost the whole transparent conductive layer(TCL), which could not be applied in the conventional p-side-up LEDs due to the electrodeshading effect. Therefore, the widened p-electrode improves the current spreading property and the uniformity of luminescence. The working voltage and series resistance are thereby reduced. The light output of embedded wide p-electrode LEDs on Cu is enhanced by 147% at a driving current of 350 m A, in comparison to conventional LEDs on Si.
Group Ⅲ-nitride material system possesses some unique properties,such as large spectrum coverage from infrared to deep ultraviolet,wide energy band gap,high electron saturation velocity,high electrical breakdown field,and strong polarization effect,which enables the big family has a very wide application range from optoelectronic to power electronic area.Furthermore,the successful growth of GaN-related III-nitride material on large size silicon substrate enable the above applications easily realize the commercialization,because of the cost-effective device fabrication on the platform of Si-based integrated circuits.In this article,the progress and development of the GaN-based materials and light-emitting diodes grown on Si substrate were summarized,in which some key issues regarding to the material growth and device fabrication were reviewed.
利用模拟软件研究施主表面态特性与AlGaN/GaN异质结构中二维电子气(2dimensional electron gas,2DEG)形成之间的关系,分析施主表面态电离过程以及表面态能级位置、表面态密度的影响。结果表明:施主表面态为2DEG的电子来源;AlGaN能带分布及2DEG密度随AlGaN厚度、施主表面态能级位置、施主表面态密度的改变而改变。
Migration characterizations of Ga and In adatoms on the dielectric surface in selective metal organic vapor phase epitaxy(MOVPE) were investigated. In the typical MOVPE environment, the selectivity of growth is preserved for Ga N,and the growth rate of Ga N micro-pyramids is sensitive to the period of the patterned SiO2 mask. A surface migration induced model was adopted to figure out the effective migration length of Ga adatoms on the dielectric surface. Different from the growth of Ga N, the selective area growth of In Ga N on the patterned template would induce the deposition of In Ga N polycrystalline particles on the patterned SiO2 mask with a long period. It was demonstrated with a scanning electron microscope and energy dispersive spectroscopy that the In adatoms exhibit a shorter migration length on the dielectric surface.
In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.
