The static recrystallization process of a cold-rolled Mg-Zn-Gd alloy was tracked by a quasi-in-situ electron backscatter diffraction method to investigate the orientations of nuclei.The results show that orientation distribution of nuclei is associated with nucleation mechanism.The continuous static recrystallization nuclei display similar orientations to the parent grains with TD orientation.Differently,discontinuous static recrystallization nuclei formed within the parent grains(TD-45~0 orientation) show random orientations and a variety of misorientation angles but preferred axes <5273> or <5270>.Interestingly,a special oriented nucleation is found.Discontinuous static recrystallization nuclei originated from boundaries of the parent grain(TD-70° orientation) show concentrated TD orientations in another side due to the preferred misorientation relationship 70°<1120>(∑18 b).It is speculated that these two special misorientation relationships are related to the dislocation type.
The extruded Mg-7Y-1Nd-0.5Zr(wt%)alloy were performed to the same strain hot rolling with different temperatures.The microstructure and texture evolution of the sheets were investigated by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),and electron back-scattered diffraction(EBSD).The results indicate that the microstructure becomes homogeneous after hot rolling process and precipitated phase distributes at grain boundaries along rolling direction.With the increase in rolling temperature,the grains of sheet grow up.The sheet rolling at 400℃is composed of recrystallization grains,the necklace of the precipitated phase in the grain boundaries and excessive dislocations.The structure of necklace of the precipitated phase is fcc structure with lattice constant of a=0.75 nm.With rolling temperatures increasing from 400 to 450℃,the content of recrystallized grains in volume fraction with relatively random orientations increases significantly.Compared with the rolling process at 400℃,the amount of precipitated phases is reduced at the grain boundary,and the precipitated phase begins to appear in the grain interior when rolling at 450℃.The structure of the precipitated phase is fcc with lattice constant of a=2.22 nm.The recrystallization grains begin to grow in the rolling process at 500℃.The basal texture is obviously produced during the rolling process at 400 and 450℃;however,the basal texture is weak in the rolling process at 500℃.
Jing-Bao LiuKui ZhangJing-Tao HanXing-Gang LiYong-Jun LiMing-Long MaJia-Wei YuanGuo-Liang Shi
The influence of grain size on the tensile deformation and ductility for Mg–1.02%Zn(wt.%)alloy was investigated.The uniform elongation is nearly insensitive to the increase of grain size,but the post-uniform elongation is significantly decreased with increasing grain size.The high ductility in the fine-grained samples is due to the lower frequency of twins and increased dynamic recovery from the enhanced activation of prismaticslip.
Hot isostatic pressing (HIP) was applied to Mg-6Gd-3Y-0.5Zr (GW63) alloy to reduce shrinkage porosity, thus, to enhance the integrity and reliability of castings. During HIP process, shrinkage porosity was closed by grain compatible deformation and subsequent diffusion across the bonding interface. The amount of initial shrinkage porosity was the key factor for shrinkage porosity closure. HIP was testified to be effective on shrinkage porosity reduction in GW63 alloy due to its relatively narrow solidification range and resultant low content of initial shrinkage porosity in most sections, leading to higher tensile properties both in as-cast and cast-T6 condition. The improvement in tensile properties was mainly because of shrinkage porosity reduction and resultant effective rare-earth (RE) elements homogenization and precipitation strengthening.
In order to study the effect of Zr modification and riser size on microporosity defect distributions in WE54 alloy sand castings,the microporosity volume percentage in Zr-free and Zr-containing WE54 alloy plate castings was determined by density measurement based on Archimedes' principle,and the microstructure of the microporosity defects was observed by optical microscopy and scanning electron microscopy.Then by using Procast software,the Niyama criterion was calculated in order to investigate the validity of Niyama criterion on prediction of microporosity defects in WE54 alloy sand castings.It is found from the density measurement results that Zr addition does not affect the microporosity distributions in WE54 alloy castings.While the distribution area of microporosity defect in the plate castings decreases significantly as the riser size increases.Based on the experimental results,a riser selection principle for production of compact WE54 alloy castings is proposed that the solidification modulus of the riser should be greater than that of the casting by 30%,simply m_r > 1.3m_c.By comparing the experimental and simulating results,it is found that the predicted microporosity regions by Niyama criterion agrees well with experimental results,and a critical Niyama value of0.4 ℃^(0.5) s^(0.5) mm^(-1) is suggested for prediction of microporosity formation in WE54 alloy sand castings.
